configs/orange-pi-zero-plus2: enable WiFi support

Orange-Pi Zero Plus2 board has AP6212 WiFi/BT combo, but does not have ethernet port. So it makes sense to enable wireless networking by default: - add DTS patch enabling AP6212 WiFi/BT combo support -- this patch is on its way to mainline Linux v4.16 - enable WiFi support in kernel config - enable Broadcom brcmfmac kernel driver in kernel config - add Broadcom wireless firmware package to image - add basic wireless tools to image - add mdev to image to enable module autoloading - add rootfs overlay with proper NVRAM file for on-board AP6212 chip Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com> Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
2026-09-30 22:11:59 -09:00 · 2018-02-11 18:56:49 +03:00
parent 5c5f274601
commit 53ae154c77
4 changed files with 153 additions and 1 deletions
--- a/board/orangepi/orangepi-zero-plus2/linux-extras.config
+++ b/board/orangepi/orangepi-zero-plus2/linux-extras.config
@@ -0,0 +1,10 @@
+# wireless core
+CONFIG_WIRELESS=y
+CONFIG_CFG80211=y
+CONFIG_MAC80211=y
+CONFIG_CFG80211_WEXT=y
+
+# wireless drivers
+CONFIG_WLAN=y
+CONFIG_WLAN_VENDOR_BROADCOM=y
+CONFIG_BRCMFMAC=m
--- a/board/orangepi/orangepi-zero-plus2/patches/linux/linux-0001-arm64-dts-orange-pi-zero-plus2-enable-ap6212.patch
+++ b/board/orangepi/orangepi-zero-plus2/patches/linux/linux-0001-arm64-dts-orange-pi-zero-plus2-enable-ap6212.patch
@@ -0,0 +1,73 @@
+From: Sergey Matyukevich <geomatsi@gmail.com>
+Date: Sun, 11 Feb 2018 16:21:43 +0300
+Subject: [PATCH] arm64: dts: orange-pi-zero-plus2: enable AP6212a WiFi/BT combo
+
+Enable AP6212a WiFi/BT combo chip on orange-pi-zero-plus2 board:
+- WiFi SDIO interface is connected to MMC1
+- WiFi REG_ON pin connected to gpio PA9: attach to mmc-pwrseq
+- WiFi HOST_WAKE pin connected to gpio PL7
+- BT is connected to UART1
+
+Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
+Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
+---
+ .../allwinner/sun50i-h5-orangepi-zero-plus2.dts    | 32 ++++++++++++++++++++++
+ 1 file changed, 32 insertions(+)
+
+diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-zero-plus2.dts b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-zero-plus2.dts
+index a42fd79a62a3..d415b7b67cce 100644
+--- a/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-zero-plus2.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-zero-plus2.dts
+@@ -64,6 +64,13 @@
+ 		regulator-min-microvolt = <3300000>;
+ 		regulator-max-microvolt = <3300000>;
+ 	};
+
+	wifi_pwrseq: wifi_pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		pinctrl-names = "default";
+		reset-gpios = <&pio 0 9 GPIO_ACTIVE_LOW>; /* PA9 */
+		post-power-on-delay-ms = <200>;
+	};
+ };
+ 
+ &mmc0 {
+@@ -75,6 +82,25 @@
+ 	status = "okay";
+ };
+ 
+&mmc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc1_pins_a>;
+	vmmc-supply = <&reg_vcc3v3>;
+	vqmmc-supply = <&reg_vcc3v3>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	bus-width = <4>;
+	non-removable;
+	status = "okay";
+
+	brcmf: wifi@1 {
+		reg = <1>;
+		compatible = "brcm,bcm4329-fmac";
+		interrupt-parent = <&r_pio>;
+		interrupts = <0 7 IRQ_TYPE_LEVEL_LOW>;	/* PL7 */
+		interrupt-names = "host-wake";
+	};
+};
+
+ &mmc2 {
+ 	pinctrl-names = "default";
+ 	pinctrl-0 = <&mmc2_8bit_pins>;
+@@ -90,3 +116,9 @@
+ 	pinctrl-0 = <&uart0_pins_a>;
+ 	status = "okay";
+ };
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
+	status = "okay";
+};
+-- 
+2.16.1
+
--- a/board/orangepi/orangepi-zero-plus2/rootfs_overlay/lib/firmware/brcm/brcmfmac43430-sdio.txt
+++ b/board/orangepi/orangepi-zero-plus2/rootfs_overlay/lib/firmware/brcm/brcmfmac43430-sdio.txt
@@ -0,0 +1,54 @@
+#AP6212_NVRAM_V1.0_20140603
+# 2.4 GHz, 20 MHz BW mode
+
+# The following parameter values are just placeholders, need to be updated.
+manfid=0x2d0
+prodid=0x0726
+vendid=0x14e4
+devid=0x43e2
+boardtype=0x0726
+boardrev=0x1101
+boardnum=22
+macaddr=00:90:4c:c5:12:38
+sromrev=11
+boardflags=0x00404201
+xtalfreq=26000
+nocrc=1
+ag0=255
+aa2g=1
+ccode=ALL
+
+pa0itssit=0x20
+extpagain2g=0
+
+#PA parameters for 2.4GHz, measured at CHIP OUTPUT
+pa2ga0=-168,7161,-820
+AvVmid_c0=0x0,0xc8
+cckpwroffset0=5
+
+# PPR params
+maxp2ga0=90
+txpwrbckof=6
+cckbw202gpo=0x5555
+legofdmbw202gpo=0x77777777
+mcsbw202gpo=0xaaaaaaaa
+
+# OFDM IIR :
+ofdmdigfilttype=7
+# PAPD mode:
+papdmode=2
+
+il0macaddr=00:90:4c:c5:12:38
+wl0id=0x431b
+
+#OOB parameters
+hostwake=0x40
+hostrdy=0x41
+usbrdy=0x03
+usbrdydelay=100
+deadman_to=0xffffffff
+# muxenab: 0x1 for UART enable, 0x10 for Host awake
+muxenab=0x10
+# CLDO PWM voltage settings - 0x4 - 1.1 volt
+#cldo_pwm=0x4
+