In Buildroot 2025.02, the vendor specific kernel version used for the
rapsberrypi5 does not yet include any dts named bcm2712-rpi-500.dts, which
results in a build error.
This reverts commit fa0ee12fcc, which was
mistakenly cherry picked regardless of the needed vendor kernel version bump.
Signed-off-by: Titouan Christophe <titouan.christophe@mind.be>
The VideoCore blobs for the Raspberry Pi 1, 2, 3, Zero, Zero W and Zero
2 W are differents from the ones for the Raspberry Pi 4 and the Compute
Module 4.
The VideoCore blobs for the Raspberry Pi 4 are named with a 4[1] (i.e.
start4.elf, start4x.elf, start4db.elf and start4cd.elf).
This precises which VideoCore firmware blob files are present on the
Raspberry Pi 1, 2, 3, Zero W, Zero 2 W and which files are present on
the the Rapsberry Pi 4 and the Compute Module 4.
Note: The VideoCore blobs for the Raspberry Pi 5 are self-contained in
its bootloader EEPROM[1][2]; there is no additional files for pi5.
[1]: https://www.raspberrypi.com/documentation/computers/configuration.html#start-elf
[2]: https://www.raspberrypi.com/documentation/computers/config_txt.html#start_file-fixup_file
Signed-off-by: Gaël PORTAY <gael.portay+rtone@gmail.com>
Signed-off-by: Julien Olivain <ju.o@free.fr>
(cherry picked from commit 7ebcfe3cb9)
Signed-off-by: Thomas Perale <thomas.perale@mind.be>
Any Raspberry Pi may use device-tree overlays; it is not restricted to
Raspberry Pi 3 and 4.
The defconfigs for the Raspberry Pi 3, 4, 400, Zero W, Zero 2 W, Compute
Module 4 and 4s use the miniuart-bt dtoverlay to switch the Bluetooth to
the mini-UART (ttyS0) and restore UART0 (ttyAMA0) over GPIOs 14 and 15
to enable the serial console (like the Raspberry Pi 1 and 2 that have no
Bluetooth)[1][2].
As a consequence, the Raspberry Pi Zero W, Zero 2 W, 400, Compute Module
4 and 4s install the device-tree overlays as well.
This rewords the note by adding the three missing hardwares installing
the images/rpi-firmware/overlays directory. It rewords the miniuart note
at the same time.
[1]: https://www.raspberrypi.com/documentation/computers/configuration.html#uarts-and-device-tree
[2]: https://github.com/raspberrypi/linux/blob/rpi-6.6.y/arch/arm/boot/dts/overlays/miniuart-bt-overlay.dts#L4-L6
Signed-off-by: Gaël PORTAY <gael.portay+rtone@gmail.com>
Signed-off-by: Julien Olivain <ju.o@free.fr>
(cherry picked from commit a642bed09a)
Signed-off-by: Thomas Perale <thomas.perale@mind.be>
This installs the device-tree blobs for the Compute Module 4 and Compute
Module 4s.
Signed-off-by: Gaël PORTAY <gael.portay@rtone.fr>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
There are two kind of device-tree blobs up to the Rasperry Pi 3[1][2]:
- the downstream dtbs are named after the die name (i.e. BCM27xx)
- the upstream dtbs are name after the package name (i.e. BCM283x)
Every defconfigs install exclusively the downstream device-tree blob, at
the exception of the raspberrypi3_64_defconfig that installs both since
the begining.
This removes the upstream device-tree blob for the beauty of
consistency.
Note: It is possible to load the upstream device-tree using the
upstream_kernel property[3].
Raspberry Pi, Compute Module, Raspberry Pi Zero and Raspberry Pi Zero W
use bcm2835 for upstream and bcm2708 for downstream.
Raspberry Pi 2 uses bcm2836 for upstream and bcm2709 for downstream.
Raspberry Pi 2 rev 1.2, Raspberry Pi 3, Compute Module 3/3+ and
Raspberry Zero 2 W use bcm2837 for upstream and bcm2709 for downstream.
Raspberry Pi 4/400 and Compute Module 4/4s uses bcm2711 and Raspberry Pi
5 uses bcm2712.
[1]: https://github.com/raspberrypi/linux/issues/3237
[2]: https://www.raspberrypi.com/documentation/computers/raspberry-pi.html#flagship-series
[3]: https://www.raspberrypi.com/documentation/computers/legacy_config_txt.html#upstream_kernel
Signed-off-by: Gaël PORTAY <gael.portay@rtone.fr>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
This reverts commit 6021f3678b.
That change is no more relevant since the genimage.cfg files are
generated by the commit e37ee5acdc (board/raspberrypi/post-image.sh:
generate genimage config from template if not present), and since the
variant-specific files were dropped off by the commit fc5cdeed72
(board/raspberrypi: drop variant-specific genimage files).
This removes the very last alive piece of change of the commit
6021f3678b (board/raspberrypi: handle dtb overlays for all variants);
the commit is fully reverted now.
Signed-off-by: Gaël PORTAY <gael.portay@rtone.fr>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This fixes a typo by dropping off the spurious x in ensure.
Signed-off-by: Gaël PORTAY <gael.portay@rtone.fr>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Now that we have a template generating an equivalent genimage configuration.
The generated genimage is identical to these +/- file ordering and a
trailing comma / newline that is ignored by genimage, E.G. for rpi3-64:
@@ -8,9 +8,10 @@
"rpi-firmware/cmdline.txt",
"rpi-firmware/config.txt",
"rpi-firmware/fixup.dat",
- "rpi-firmware/start.elf",
"rpi-firmware/overlays",
- "Image"
+ "rpi-firmware/start.elf",
+ "Image",
+
}
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
The rpi genimage configurations are all identical, except for the boot
partition files, which include:
- Device tree files (*.dtb)
- rpi-firmware files (rpi-firmware/*)
- Kernel image (Image/zImage)
All of these are quite simple to figure out programmatically based on the
content of BINARIES_DIR, so extend post-image.sh to fall back to generating
a genimage configuration based on genimage.cfg.in if a board specific one
does not exist.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Most of the users use HDMI console on RPi and with increasing popularity
of systemd they face a trouble.
systemd doesn't use /etc/inittab, enable getty@tty1.service instead.
Signed-off-by: Alexey Roslyakov <alexey.roslyakov@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Most rpi defconfigs use dtb overlays, but not rpi0 / rpi2 - Making it harder
to use overlays on those boards as the genimage files have to be tweaked.
To fix this, create the rpi-firmware/overlays directory in the post-build
script if needed and unconditionally include it in the genimage files so
rpi0/rpi2 works consistently with the other variants.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Currently, the cmdline.txt file is installed in $(BINARIES_DIR) by the
rpi-firmware package. Overriding files in there can not be done with an
overlay (which only applies to $(TARGET_DIR)), and thus requires using
either a post-build or post-image script, which is not always very
practical when a custom file must be used.
Like was done in 689b9ac439 (package/rpi-firmware: rework boot/config
file handling) for config.txt, add an option to allow users to specify
the path to a custom cmdline.txt.
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
Cc: Peter Seiderer <ps.report@gmx.net>
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
The CM4 IO Board is equipped with an on-board RTC connected over I2C,
and has USB 2.0 host ports.
This commit loads the appropriate overlays to enable both. The USB 2.0
interface is by default disabled on CM4 to reduce the power
consumption so it needs to be explicitly enabled on the CM4 IO Board
to use the USB ports.
Signed-off-by: Peter Seiderer <ps.report@gmx.net>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The CM4 IO Board is equipped with an on-board RTC connected over I2C,
and has USB 2.0 host ports.
This commit loads the appropriate overlays to enable both. The USB 2.0
interface is by default disabled on CM4 to reduce the power
consumption so it needs to be explicitly enabled on the CM4 IO Board
to use the USB ports.
Signed-off-by: Peter Seiderer <ps.report@gmx.net>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The Raspberry-Pi Zero 2 W is an affordable single board computer. It is
a more powerful drop-in replacement for the Raspberry Pi Zero W.
The board incorporates an Raspberry-Pi RP3A0 system-in-package (SiP) with
a Broadcom BCM2710A1 and 512MB LPDDR2 SDRAM. The CPU is a quad-core 1Ghz
64-bit Arm Cortex-A53. As for other Raspberry-Pis it also provides
2.4GHz 802.11 b/g/n Wifi, Bluetooth 4.2 and BLE.
The BCM2710 cpu is similar to the Raspberry-Pi 3, it uses the same
kernel configuration as the Raspberry-Pi 2 and 3.
Signed-off-by: Julien Grossholtz <julien.grossholtz@openest.io>
[Based on https://patchwork.ozlabs.org/project/buildroot/patch/20211030213600.3445223-3-julien.grossholtz@openest.io/
- reformat genimage-raspberrypizero2w.cfg according to the beautify patch-set
- update kernel version to 9878a11 (5.10.78)
- use new bcm2710-rpi-zero-2-w dtb
- update commit log about kernel config (RPi2/3)
- add DEVELOPERS entries for Julien
]
Signed-off-by: Peter Seiderer <ps.report@gmx.net>
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
Add missing dtb files:
- bcm2708-rpi-cm.dtb from genimage-raspberrypi.cfg
- bcm2708-rpi-zero.dtb from genimage-raspberrypi0.cfg:
- bcm2708-rpi-zero-w.dtb from genimage-raspberrypi0w.cfg
- bcm2710-rpi-cm3.dtb from genimage-raspberrypi3.cfg
- bcm2837-rpi-3-b.dtb from genimage-raspberrypi3-64.cfg
Signed-off-by: Peter Seiderer <ps.report@gmx.net>
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
Beatify this genimage .cfg file to have consistency with all genimage .cfg
files in Buildroot.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Beatify this genimage .cfg file to have consistency with all genimage .cfg
files in Buildroot.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Beatify this genimage .cfg file to have consistency with all genimage .cfg
files in Buildroot.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Beatify this genimage .cfg file to have consistency with all genimage .cfg
files in Buildroot.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Beatify this genimage .cfg file to have consistency with all genimage .cfg
files in Buildroot.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Beatify this genimage .cfg file to have consistency with all genimage .cfg
files in Buildroot.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Beatify this genimage .cfg file to have consistency with all genimage .cfg
files in Buildroot.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Beatify this genimage .cfg file to have consistency with all genimage .cfg
files in Buildroot.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Beatify this genimage .cfg file to have consistency with all genimage .cfg
files in Buildroot.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Beatify this genimage .cfg file to have consistency with all genimage .cfg
files in Buildroot.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Try to be less smart (focused on the one target/one use-case),
instead reduce the rpi-firmware package to a selectable list
of (verbatim) installed firmware files.
- change rpi-firmware config handling from rpi-variant/rpi-flavour
choices to bootcode.bin, pi-default/-extended/-cut-down and
pi4-/default/-extended/-cut-down selection
- add BR2_PACKAGE_RPI_FIRMWARE_CONFIG_FILE option to select installable
config.txt file
- remove config.txt modify code/handling from raspberry post-image.sh
script
- add different customized config.txt files to the raspberry board
section
- change dtoverlay krnbt from 'dtoverlay=miniuart-bt,krnbt=on' to extra line
with explanation comment
- change raspberry defconfigs to select appropiate rpi-firmware
and config.txt files
- change genimage-raspberrypi4.cfg/genimage-raspberrypi4-64.cfg to
use start4.elf and fixup4.dat
- update board/raspberrypi/readme.txt (add optional files fixup4.dat,
start4.elf and zImage)
With this changes a better support for custom use-cases should
be possible, specially multi-target SD cards as suggested by
Stefan Agner ([1]).
[1] http://lists.busybox.net/pipermail/buildroot/2021-February/303318.html
Signed-off-by: Peter Seiderer <ps.report@gmx.net>
[yann.morin.1998@free.fr: fix case of no config.txt provided]
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
The default setting with miniuart-bt requires hciattach which is a
deprecated utility in BlueZ. Setting the krnbt parameter switches to
the modern method of using serdev in the kernel removing the need for
any userspace configuration to enable the Bluetooth controller.
This is documented as applying to all Raspberry Pi variants so just
enable it globally.
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
