Back in commit
44a6b7866c ("configs/qemu_sh4*: switch
to initramfs"), the Qemu SuperH defconfigs were switched to initramfs
due to a bug in the Qemu disk emulation.
However, the initramfs solution has an issue: if the initramfs is
slightly too large (like just 6 MB!), the system no longer boots.
Since the disk emulation problem has apparently been resolved in Qemu
10 (according to testing), let's switch back to this.
In addition to essentially reverting
44a6b7866c, we also need to adjust the
kernel configuration so that the kernel takes its command line for the
bootloader (in our case from the Qemu -append option). Otherwise an
hardcoded command line is used, which doesn't mount /dev/sda as the
root filesystem.
This update has been tested on Gitlab CI:
https://gitlab.com/tpetazzoni/buildroot/-/pipelines/1968267919
Thanks to Romain Naour for pointing to the initramfs size as being the
issue.
Cc: Romain Naour <romain.naour@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Julien Olivain <ju.o@free.fr>
(cherry picked from commit 5edce69188)
Signed-off-by: Thomas Perale <thomas.perale@mind.be>
In Buildroot 2025.02, the vendor specific kernel version used for the
rapsberrypi5 does not yet include any dts named bcm2712-rpi-500.dts, which
results in a build error.
This reverts commit fa0ee12fcc, which was
mistakenly cherry picked regardless of the needed vendor kernel version bump.
Signed-off-by: Titouan Christophe <titouan.christophe@mind.be>
Actually DTB_LIST accepts only file and not files with relative path
preprended. This leads to have vfat without .dtb files and so Linux
doesn't start. Let's fix this by including slash in sed command as done
for mxc as well as basename in front of $dt.dtb to remove possible
useless folders present in the dts path. Let's also add set -e at the
top of the script to make it more verbose on error and modify this
section according to spellcheck as done for mxc.
This commit align this "mxs/post-image.sh" with its "imx/post-image.sh"
counterpart which was improved for arm64 in commit [1].
[1] 4755bf2bd4
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
[Julien:
- change space indentation to tabs for consistency
- add note in commit log about imx/post-image.sh
]
Signed-off-by: Julien Olivain <ju.o@free.fr>
(cherry picked from commit 50297207a8)
Signed-off-by: Thomas Perale <thomas.perale@mind.be>
If an attempt is made to create a UBI volume and it already exists, the
operation fails. Therefore, before requesting the creation of a UBI
volume, we erase the entire NAND to ensure that no errors occur.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
(cherry picked from commit 97ac89eb11)
Signed-off-by: Thomas Perale <thomas.perale@mind.be>
Fix the board flashing by adding the bootloader, which I had mistakenly
forgotten to include in the script.
Fixes: 322e8d8451 ("configs/imx6ulz_bsh_smm_m2_defconfig: new defconfig")
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Signed-off-by: Julien Olivain <ju.o@free.fr>
(cherry picked from commit a7ea1e658d)
Signed-off-by: Thomas Perale <thomas.perale@mind.be>
This commit adds BR2_DOWNLOAD_FORCE_CHECK_HASHES=y in the defconfig
and adds custom hash files. The exception entry in .checkpackageignore
is also removed.
Cc: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Julien Olivain <ju.o@free.fr>
(cherry picked from commit 683681261b)
Signed-off-by: Thomas Perale <thomas.perale@mind.be>
The "modprobe brcmfmac" command is not necessary because this driver
is automatically loaded.
Remove the "iwconfig" line as it is considered deprecated:
warning: `iwconfig' uses wireless extensions which will stop working for Wi-Fi 7 hardware; use nl80211
Remove the "-Dwext" parameter as it is not supported by the default kernel
configuration:
wlan0: Unsupported driver 'wext'
Tested Wifi by following the updated commands.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Julien Olivain <ju.o@free.fr>
(cherry picked from commit 6240b75d0c)
Signed-off-by: Thomas Perale <thomas.perale@mind.be>
The patch bumps the Linux kernel to version 6.1.133. The size of xipImage
has increased by only 22 bytes (1671804 bytes compared to 1671782 in
version 6.1.126).
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
(cherry picked from commit cb6729d214)
Signed-off-by: Thomas Perale <thomas.perale@mind.be>
The VideoCore blobs for the Raspberry Pi 1, 2, 3, Zero, Zero W and Zero
2 W are differents from the ones for the Raspberry Pi 4 and the Compute
Module 4.
The VideoCore blobs for the Raspberry Pi 4 are named with a 4[1] (i.e.
start4.elf, start4x.elf, start4db.elf and start4cd.elf).
This precises which VideoCore firmware blob files are present on the
Raspberry Pi 1, 2, 3, Zero W, Zero 2 W and which files are present on
the the Rapsberry Pi 4 and the Compute Module 4.
Note: The VideoCore blobs for the Raspberry Pi 5 are self-contained in
its bootloader EEPROM[1][2]; there is no additional files for pi5.
[1]: https://www.raspberrypi.com/documentation/computers/configuration.html#start-elf
[2]: https://www.raspberrypi.com/documentation/computers/config_txt.html#start_file-fixup_file
Signed-off-by: Gaël PORTAY <gael.portay+rtone@gmail.com>
Signed-off-by: Julien Olivain <ju.o@free.fr>
(cherry picked from commit 7ebcfe3cb9)
Signed-off-by: Thomas Perale <thomas.perale@mind.be>
Any Raspberry Pi may use device-tree overlays; it is not restricted to
Raspberry Pi 3 and 4.
The defconfigs for the Raspberry Pi 3, 4, 400, Zero W, Zero 2 W, Compute
Module 4 and 4s use the miniuart-bt dtoverlay to switch the Bluetooth to
the mini-UART (ttyS0) and restore UART0 (ttyAMA0) over GPIOs 14 and 15
to enable the serial console (like the Raspberry Pi 1 and 2 that have no
Bluetooth)[1][2].
As a consequence, the Raspberry Pi Zero W, Zero 2 W, 400, Compute Module
4 and 4s install the device-tree overlays as well.
This rewords the note by adding the three missing hardwares installing
the images/rpi-firmware/overlays directory. It rewords the miniuart note
at the same time.
[1]: https://www.raspberrypi.com/documentation/computers/configuration.html#uarts-and-device-tree
[2]: https://github.com/raspberrypi/linux/blob/rpi-6.6.y/arch/arm/boot/dts/overlays/miniuart-bt-overlay.dts#L4-L6
Signed-off-by: Gaël PORTAY <gael.portay+rtone@gmail.com>
Signed-off-by: Julien Olivain <ju.o@free.fr>
(cherry picked from commit a642bed09a)
Signed-off-by: Thomas Perale <thomas.perale@mind.be>
As the mender_x86_64_efi_defconfig does not build the xz package, creating a
boostrap image with a lzma compression results in the following error on boot:
```
Error while handling bootstrap Artifact, continuing: invalid bootstrap
Artifact: readHeaderV3: handleHeaderReads: readHeader: readNext: Failed to get
next header: reader: error reading archive: unexpected EOF
```
This also results in the same error for the generated mender image, as it's
also created with lzma compression unconditionally.
Set the compression to none to resolve the above error.
Signed-off-by: Adam Duskett <adam.duskett@amarulasolutions.com>
Signed-off-by: Julien Olivain <ju.o@free.fr>
Currently, the post-build.sh script adds device_type to /var/lib/mender,
however, this doesn't work for two reasons:
1) /data/ mounts to /var/lib/mender
2) The device_type location in mender.conf points to /etc/mender/device_type.
This leads to an error during the bootstrap process because mender reads the
default device_type file installed by mender.mk in /etc/mender, leading to the
following error:
```
Error while handling bootstrap Artifact, continuing: invalid bootstrap
Artifact: readHeaderV3: handleHeaderReads: image
(device types [buildroot-x86_64]) not compatible with device BUILDROOT_DEVICE
```
Set the creation of the device_type file in board/mender/x86_64/post-build.sh
to /etc/mender/device_type to fix the error.
Signed-off-by: Adam Duskett <adam.duskett@amarulasolutions.com>
Signed-off-by: Julien Olivain <ju.o@free.fr>
Enable FORCE_CHECK_HASHES to ensure that all hashes are valid even
from custom packages.
Add custom version package hashes of Linux, U-boot and TF-A.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Now that all Xilinx boards have been bumped to Linux 6.6.70, the Linux 6.6.60
hash can be removed.
Signed-off-by: Neal Frager <neal.frager@amd.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Add a new defconfig for the imx93-evk board that uses upstream
components, such as:
- Linux Kernel: Upstream version 6.12.16
- U-boot: Upstream version 2025.01
- ATF: Upstream version 2.12
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Julien Olivain <ju.o@free.fr>
Since commit dc0f7215c6 ("package/gcc: switch to 13.x as default"),
the Linux kernel is failing to build with this output:
In file included from ./include/linux/kernel.h:10,
from drivers/ata/libahci.c:35:
drivers/ata/libahci.c: In function ‘ahci_led_store’:
./include/linux/compiler.h:348:45: error: call to ‘__compiletime_assert_1154’ declared with attribute error: BUILD_BUG_ON failed: sizeof(_s) > sizeof(long)
348 | _compiletime_assert(condition, msg, __compiletime_assert_, __LINE__)
Fix it by importing Linux upstream patch.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This patch adds the hash for Linux version 6.6.70 for Xilinx boards.
Signed-off-by: Neal Frager <neal.frager@amd.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
